10年品牌值得信賴
精誠團結、奮起拼搏、開拓進取

濟南彩鋼板

13969159292

0531-88686388

新聞中心

首頁>>新聞中心>>濟南彩鋼瓦的安裝焊接程序
新聞中心
聯系我們
濟南堅固彩鋼工程公司

聯系人:

電話:13969159292

地址:濟南市工業北路81號北鄰

濟南彩鋼瓦的安裝焊接程序

來源:http://www.ebassfish.com/ 日期:2021-03-02 發布人:jiangucaigang
說到濟南彩鋼瓦,想來大家應該都很熟悉,生活中彩鋼瓦的應用是非常廣泛的,所以是比較常見的。那你知道彩鋼瓦的安裝焊接程序有哪些嗎?濟南復合板廠家帶你一起了解一下,希望能幫助到你!
When it comes to Jinan color steel tile, I think everyone should be very familiar with it. The application of color steel tile in life is very extensive, so it is more common. Do you know the installation and welding procedures of color steel tile? Jinan composite board manufacturers take you to understand, hope to help you!
彩鋼瓦的電焊焊接部位為柱-柱橫焊、柱-梁平焊(包含桁架結構梁左右翼緣平焊)、T型角立焊,焊縫方式及規格按設計方案規定.彩鋼瓦電焊焊接的一般次序為:焊接前查驗→加熱防銹處理→裝焊墊塊和引弧板→電焊焊接→檢測.
The electric welding parts of color steel tile are column column horizontal welding, column beam flat welding (including truss structure beam left and right flange flat welding), t-angle vertical welding. The welding method and specification are according to the design scheme. The general welding sequence of color steel tile is: inspection before welding → heating antirust treatment → welding pad and arc striking plate → electric welding → inspection
1.一個插口務必持續焊完,如迫不得已而半途停焊時,應開展隔熱保溫緩冷暴力,再焊接前,應再次按照規定加溫.
1. A socket must be continuously welded. If it is forced to stop welding halfway, heat insulation and slow cooling should be carried out. Before re welding, it should be heated again according to the regulations
2.逢雨、下雪天時應停焊,預制構件焊縫周邊及上邊需有檔風、雨蓬,風力超過5m/s時應停焊.工作溫度小于零度時,應按照規定采用加熱和后熱對策工程施工.
2. Welding shall be stopped in rainy and snowy days. There shall be wind baffle and canopy around and above the welding seam of prefabricated components. Welding shall be stopped when the wind force exceeds 5m / s. when the working temperature is less than 0 ℃, heating and post heating measures shall be adopted for engineering construction according to regulations
3.碳素鋼應在焊接制冷到工作溫度、低合金工具鋼應在進行24小時之后,開展焊接探傷檢測檢測.
3. Carbon steel should be cooled to working temperature after welding, and low alloy tool steel should be tested after 24 hours
4.電焊工和檢測工作人員要用心填好工作記錄卡.濟南彩鋼瓦焊后外型及超音波查驗達標后抽樣開展了結構力學和物理學實驗.
4. Welders and inspection workers should carefully fill in the work record card. After the appearance and ultrasonic inspection of Jinan color steel tile reached the standard, the structural mechanics and physics experiments were carried out
5.焊接前查驗焊縫視角、鈍邊、空隙及錯口量,焊縫內和兩邊的銹跡、油漬、氧化鐵皮等應消除整潔.
5. Before welding, check the weld angle, blunt edge, gap and stagger amount, and remove rust, oil stains and oxide scales in and on both sides of the weld
6.加熱.焊接前用氣割或特別制作烤槍對焊縫以及兩邊各100毫米范疇內的對接焊縫勻稱加溫,并且用表層測溫計測量溫度,避免溫度不符合規定或表層部分空氣氧化,加熱溫度.
6. Heating. Before welding, use gas cutting or special baking gun to evenly heat the welding seam and butt welding seam within the scope of 100 mm on both sides, and use surface thermometer to measure the temperature, so as to avoid the temperature not conforming to the regulations or partial air oxidation on the surface and heating temperature
7.再次查驗加熱溫度,如溫度不足應再次加溫,使之符合規定.
7. Check the heating temperature again. If the temperature is not enough, heat it again to make it meet the requirements
8.裝焊墊塊及引弧板,其表層清理水平規定與焊縫表層同樣,墊塊與對接焊縫應緊貼,引弧板與對接焊縫電焊焊接應堅固.
8. The cleaning level of surface layer of welding pad and run on plate is the same as that of weld surface layer. The pad and butt weld should be close to each other, and the electric welding of run on plate and butt weld should be firm
9.電焊焊接:一層的焊縫應封死焊縫內母材與墊塊的相接處,隨后逐道逐級累焊至鋪滿焊縫,每道焊接焊完后,都務必消除焊穿及濺出物,出現鑄造缺陷應立即磨掉并修復.
9. Electric welding: the joint between the base metal and the cushion block in the welding seam should be sealed, and then the welding seam should be welded step by step until the welding seam is covered. After each welding, the welding penetration and spatter must be eliminated, and the casting defects should be worn off and repaired immediately
彩鋼瓦焊后實驗結果連接頭的抗壓強度做到對接焊縫抗壓強度指標值,連接頭彎折180°無裂紋.彩鋼瓦選用的焊材和自動焊機技術性標準應合乎國家行業標準,特性優良.清渣、氣刨、焊絲風干隔熱保溫等設備應齊全有效.
After welding, the test results show that the compressive strength of the connector can reach the index value of the butt weld compressive strength, and the connector is bent 180 ° without cracks. The welding materials and automatic welding machine technical standards of the color steel tile should meet the national industry standards, with excellent characteristics. The slag cleaning, air gouging, welding wire air drying, heat insulation and other equipment should be complete and effective
以上就是對濟南彩鋼瓦的焊接程序介紹,相信通過本文的描述,你能夠對彩鋼瓦的焊接有一定的認識和了解,希望以上內容能幫助到你。另外,若你想要了解更多相關資訊,可以多多關注我們的網站動態:http://www.ebassfish.com
The above is the welding procedure of Jinan color steel tile, I believe that through the description of this paper, you can have a certain understanding of the color steel tile welding, I hope the above content can help you. In addition, if you want more information, you can pay more attention to our website http://www.ebassfish.com
此文關鍵詞: 濟南彩鋼瓦  

推薦閱讀/ Recommended reading

相信大家對彩鋼復合板都不會陌生,畢竟在生活中是比較常見的。雖然濟南彩鋼復合板引進不到20年時間,但由于其具有承力、保溫隔熱、裝飾、防

防火彩鋼板表面為什么出現壓斑? 2022-02-26
有哪些原因會導致C型鋼出現變形的現象? 2022-02-22
彩鋼瓦具有哪些優勢? 2022-02-17
復合板質量控制的措施及建議 2022-02-14
欧美激情视频-人妻av综合天堂一区-色天使色妺妺网站-无码a片