10年品牌值得信賴
精誠團結、奮起拼搏、開拓進取

濟南彩鋼板

13969159292

0531-88686388

新聞中心

首頁>>新聞中心>>C型鋼的厚壁質量是怎么控制的呢?
新聞中心
聯系我們
濟南堅固彩鋼工程公司

聯系人:

電話:13969159292

地址:濟南市工業北路81號北鄰

C型鋼的厚壁質量是怎么控制的呢?

來源:http://www.ebassfish.com/ 日期:2020-11-17 發布人:jiangucaigang
C型鋼的厚壁質量是怎么控制的呢?不同的用戶對C型鋼的厚度有不同的要求。假如要同時知足這些要求,所選的C型鋼出產工藝和設備非常樞紐。一般來說,冷軋很難出產出高質量的C型鋼,所以要用C型鋼機來完成。
 
How to control the thick wall quality of C-section steel? Different users have different requirements for the thickness of C-section steel. If we want to meet these requirements at the same time, the selected C-beam production process and equipment is very pivotal. Generally speaking, cold rolling is difficult to produce high-quality C-beam, so it needs to be completed by C-beam mill.
 
物料從C型鋼機尾部進入后,被各種壓輥壓下,成型后的C型鋼從機頭輸出。這不僅大大優化了必要的出產加工工藝,而且進步了產量。它還能保證C型鋼產品具有平均的壁厚和復雜的界面外形。
 
After the material enters from the tail of the C-beam machine, it is pressed down by various rollers, and the formed C-beam is exported from the machine head. This not only greatly optimizes the necessary production and processing technology, but also improves the output. It can also ensure the average wall thickness and complex interface shape of C-beam products.
 
為了達到正確的壁厚,在壓制C型鋼時,C型鋼機使用的模具由正確的上模具和一些具有相同尺寸、規格和尺寸的下模具組成。為了在加工前將它們安裝到位,不僅需要確保上模和下模的平穩運行,還需要確保附近的間隙平均,以便壓制的C形鋼可以具有平均的壁厚。
 
In order to achieve the correct wall thickness, the die used by the C-beam machine consists of the correct upper die and some lower dies with the same size, specification and size. In order to install them in place before processing, it is necessary not only to ensure the smooth operation of the upper and lower dies, but also to ensure that the adjacent gaps are even so that the pressed C-shaped steel can have an average wall thickness.
濟南c型鋼長
 
在加工C型鋼的過程中,安裝模具并對主機進行測試。然后啟動空氣壓縮機、真空泵、擠出機、切磚機、給料機、壓磚機、主機和瓷磚輸送機。泊車時,首先休止擠壓機,然后休止其余設備。
 
In the process of processing C-section steel, the mould is installed and the main engine is tested. Then start the air compressor, vacuum pump, extruder, brick cutter, feeder, brick press, host and tile conveyor. When parking, first stop the extruder and then rest of the equipment.
 
我們在使用設備前,檢查連接是否牢固,安裝螺栓螺母是否擰緊,用電啟動發念頭試運轉前,在左右底盤加足夠的潤滑油。從擠出機擠出的泥坯由切割機切割成固定長度,由輥式輸送機輸送到壓磚機,并由裝載機按照指定程序輸送到下模。將由C型鋼機壓制的磚坯在工作臺上分度后,由卸磚機的真空吸盤吸附,分度后放置在輸送線的磚坯支架上。
 
Before using the equipment, we should check whether the connection is firm, whether the mounting bolts and nuts are tightened, and add enough lubricating oil to the left and right chassis before starting the engine with electricity. The slurry extruded from the extruder is cut into a fixed length by the cutter, transported to the brick press by the roller conveyor, and transported to the lower die by the loader according to the specified procedure. After dividing the brick blank pressed by C-beam machine on the worktable, it is absorbed by the vacuum suction cup of the brick unloader, and is placed on the brick blank support of the conveying line after graduation.
 
用該C型鋼機制造的C型鋼的壁厚可以做得很薄,大大簡化了出產工藝,進步了出產效率。它可以出產各種均勻壁厚但截面復雜的型材和不同材質的冷彎彩鋼設備,這些都是普通熱軋方法難以出產的。
 
The wall thickness of C-section steel made by this machine can be made very thin, which greatly simplifies the production process and improves the production efficiency. It can produce all kinds of profiles with uniform wall thickness but complex cross-section and cold-formed color steel equipment of different materials, which are difficult to produce by ordinary hot rolling method.
 
以上是關于C型鋼的厚壁質量是怎么控制的相關介紹,希望大家看完能有所幫助,想要了解更多濟南c型鋼內容歡迎關注我們的網站。
 
The above is about how to control the thick wall quality of C-section steel. I hope you can help after reading. If you want to know more about Jinan C-section steel, please pay attention to our website.
 
此文關鍵詞: 濟南C型鋼廠  

推薦閱讀/ Recommended reading

相信大家對彩鋼復合板都不會陌生,畢竟在生活中是比較常見的。雖然濟南彩鋼復合板引進不到20年時間,但由于其具有承力、保溫隔熱、裝飾、防

防火彩鋼板表面為什么出現壓斑? 2022-02-26
有哪些原因會導致C型鋼出現變形的現象? 2022-02-22
彩鋼瓦具有哪些優勢? 2022-02-17
復合板質量控制的措施及建議 2022-02-14
欧美激情视频-人妻av综合天堂一区-色天使色妺妺网站-无码a片