10年品牌值得信賴
精誠團結、奮起拼搏、開拓進取

濟南彩鋼板

13969159292

0531-88686388

新聞中心

首頁>>新聞中心>>濟南C型鋼廠淺析C型鋼的缺陷問題特點
新聞中心
聯系我們
濟南堅固彩鋼工程公司

聯系人:

電話:13969159292

地址:濟南市工業北路81號北鄰

濟南C型鋼廠淺析C型鋼的缺陷問題特點

來源:http://www.ebassfish.com/ 日期:2020-09-22 發布人:jiangucaigang
一、C型鋼制成品焊接裂開或裂開
1、 Cracking or cracking in welding of C-section steel products
造成緣故:1、加工過程中原材料薄厚總寬不平穩。造成假焊或假焊; 2、電焊焊接時擠壓成型幅度不足,焊接結合欠佳。
The causes are as follows: 1. The thickness and width of raw materials are not stable. Results in false welding or false welding; 2. Insufficient extrusion forming range and poor welding combination.
二、商品彎折不符合規定
2、 The bending of goods does not meet the requirements
造成緣故:1、無縫鋼管壁厚不勻(原材料薄厚不勻稱或由生產制造所造成); 2、軋輥直徑的不一樣造成無縫鋼管形變不勻,造成彎折。
The causes are as follows: 1. The wall thickness of seamless steel pipe is not uniform (the thickness of raw material is uneven or caused by production); 2. The deformation of seamless steel pipe is uneven due to the difference of roll diameter, resulting in bending.
三、商品規格起伏很大
3、 The specifications of the goods fluctuate greatly
造成緣故:1、在調整軋輥時實際操作不善; 2、扎扎實實速率過快,造成規格起伏很大。
The causes are as follows: 1. The actual operation is not good when adjusting the roller; 2. The speed of down-to-earth work is too fast, resulting in large fluctuation of specifications.
四、商品橫截面毛邊狀況比較嚴重,造成“耗子小尾巴”
4、 The tail of the product is relatively small in cross section
造成緣故: 1、裁切刃口變鈍,使空隙過大非常容易殘余;木工鋸片遲緩,或安裝不善也非常容易造成毛邊的造成; 2、焊接鋼管時焊接上有擠壓不必要金屬材料。電焊焊接規章制度不標準也會讓裁切時更非常容易留有毛邊。
The causes are as follows: 1. The cutting edge becomes blunt, which makes the gap too large and easy to remain; the wood saw blade is slow or not properly installed, which is also very easy to cause burr; 2. When welding steel pipe, unnecessary metal materials are extruded on the welding. Non standard welding rules and regulations will make it easier to leave burr when cutting.
五、焊接表層不整平,凸凹顯著
5、 The welding surface is not smooth and convex
造成緣故: 1、焊接凸出,焊接刨削深層偏深,造成平整度減少。 2、焊接內凹,焊接刨削深層偏淺。
Causes: 1, welding protruding, welding planing deep depth, resulting in flatness reduction. 2. Welding concave, welding planed deep shallow.
六、方鋼管或矩形方管R角不勻稱
6、 The R-angle of square steel tube or rectangular square pipe is not symmetrical
造成緣故:生產制造實際操作不善
Cause: the actual operation of production and manufacturing is not good
七、管身存有接焊狀況
7、 There is welding condition in the pipe body
造成緣故: 在加工過程中,原材料要以卷裝開展放卷機冷軋,每卷原材料無插口,以便可以持續生產,需在兩卷原材料首末相電焊焊接。
Causes: in the process of processing, the raw materials should be cold rolled by the unwinder in the form of coils. There is no socket for each coil of raw materials, so that continuous production can be carried out. Therefore, it is necessary to weld the two coils of raw materials in the first and last phases.
八、端口號鋸切不齊整,歪斜或凸凹不平。
8、 The port number is uneven, skew or uneven.
造成緣故: 在裁切時造成裁切形變促使端口號參差不齊。
Cause: in the cutting deformation caused by cutting, resulting in uneven port number.一、C型鋼制成品焊接裂開或裂開
1、 Cracking or cracking in welding of C-section steel products
造成緣故:1、加工過程中原材料薄厚總寬不平穩。造成假焊或假焊; 2、電焊焊接時擠壓成型幅度不足,焊接結合欠佳。
The causes are as follows: 1. The thickness and width of raw materials are not stable. Results in false welding or false welding; 2. Insufficient extrusion forming range and poor welding combination.
二、商品彎折不符合規定
2、 The bending of goods does not meet the requirements
造成緣故:1、無縫鋼管壁厚不勻(原材料薄厚不勻稱或由生產制造所造成); 2、軋輥直徑的不一樣造成無縫鋼管形變不勻,造成彎折。
The causes are as follows: 1. The wall thickness of seamless steel pipe is not uniform (the thickness of raw material is uneven or caused by production); 2. The deformation of seamless steel pipe is uneven due to the difference of roll diameter, resulting in bending.
三、商品規格起伏很大
3、 The specifications of the goods fluctuate greatly
造成緣故:1、在調整軋輥時實際操作不善; 2、扎扎實實速率過快,造成規格起伏很大。
The causes are as follows: 1. The actual operation is not good when adjusting the roller; 2. The speed of down-to-earth work is too fast, resulting in large fluctuation of specifications.
四、商品橫截面毛邊狀況比較嚴重,造成“耗子小尾巴”
4、 The tail of the product is relatively small in cross section
造成緣故: 1、裁切刃口變鈍,使空隙過大非常容易殘余;木工鋸片遲緩,或安裝不善也非常容易造成毛邊的造成; 2、焊接鋼管時焊接上有擠壓不必要金屬材料。電焊焊接規章制度不標準也會讓裁切時更非常容易留有毛邊。
The causes are as follows: 1. The cutting edge becomes blunt, which makes the gap too large and easy to remain; the wood saw blade is slow or not properly installed, which is also very easy to cause burr; 2. When welding steel pipe, unnecessary metal materials are extruded on the welding. Non standard welding rules and regulations will make it easier to leave burr when cutting.
五、焊接表層不整平,凸凹顯著
5、 The welding surface is not smooth and convex
造成緣故: 1、焊接凸出,焊接刨削深層偏深,造成平整度減少。 2、焊接內凹,焊接刨削深層偏淺。
Causes: 1, welding protruding, welding planing deep depth, resulting in flatness reduction. 2. Welding concave, welding planed deep shallow.
六、方鋼管或矩形方管R角不勻稱
6、 The R-angle of square steel tube or rectangular square pipe is not symmetrical
造成緣故:生產制造實際操作不善
Cause: the actual operation of production and manufacturing is not good
七、管身存有接焊狀況
7、 There is welding condition in the pipe body
造成緣故: 在加工過程中,原材料要以卷裝開展放卷機冷軋,每卷原材料無插口,以便可以持續生產,需在兩卷原材料首末相電焊焊接。
Causes: in the process of processing, the raw materials should be cold rolled by the unwinder in the form of coils. There is no socket for each coil of raw materials, so that continuous production can be carried out. Therefore, it is necessary to weld the two coils of raw materials in the first and last phases.
八、端口號鋸切不齊整,歪斜或凸凹不平。
8、 The port number is uneven, skew or uneven.
造成緣故: 在裁切時造成裁切形變促使端口號參差不齊。
Cause: in the cutting deformation caused by cutting, resulting in uneven port number.
此文關鍵詞: 濟南C型鋼  

推薦閱讀/ Recommended reading

相信大家對彩鋼復合板都不會陌生,畢竟在生活中是比較常見的。雖然濟南彩鋼復合板引進不到20年時間,但由于其具有承力、保溫隔熱、裝飾、防

防火彩鋼板表面為什么出現壓斑? 2022-02-26
有哪些原因會導致C型鋼出現變形的現象? 2022-02-22
彩鋼瓦具有哪些優勢? 2022-02-17
復合板質量控制的措施及建議 2022-02-14
欧美激情视频-人妻av综合天堂一区-色天使色妺妺网站-无码a片