10年品牌值得信賴
精誠團結、奮起拼搏、開拓進取

濟南彩鋼板

13969159292

0531-88686388

新聞中心

首頁>>新聞中心>>C型鋼厚壁質量如何控制大家知道嗎?
新聞中心
聯系我們
濟南堅固彩鋼工程公司

聯系人:

電話:13969159292

地址:濟南市工業北路81號北鄰

C型鋼厚壁質量如何控制大家知道嗎?

來源:http://www.ebassfish.com/ 日期:2020-06-08 發布人:jiangucaigang
  不同的用戶對型鋼壁厚有不同的要求。如果要同時滿足這些要求,所選擇的濟南C型鋼廠生產工藝和設備是非常關鍵的。一般情況下,冷軋很難生產出優質的C型鋼,因此采用C型鋼軋機來完成。
  Different users have different requirements for section steel wall thickness. If we want to meet these requirements at the same time, the production process and equipment of Jinan C-steel plant is very important. In general, it is difficult to produce high quality C-section steel by cold rolling, so C-section mill is used to complete.
  物料從C型鋼尾部進入后,被各種滾輪壓下,由機頭輸出異形c梁。這不僅大大優化了必要的生產工藝,而且增加了產量。保證了c型鋼產品壁厚均勻,界面形狀復雜。
濟南C型鋼廠
  After the material enters from the tail of C-shaped steel, it is pressed down by various rollers, and the head outputs the special-shaped C-beam. This not only greatly optimizes the necessary production process, but also increases the output. The uniform wall thickness and complex interface shape of C-steel products are ensured.
  為了達到精確的壁厚,c梁壓力機所使用的模具由精確的上模具和一些相同尺寸、規格、尺寸的下模具組成。為了在加工前安裝到位,不僅要保證上、下模具的平穩運行,還要保證上、下模具周圍的間隙均勻,使壓制的c型鋼具有均勻的壁厚。
  In order to achieve accurate wall thickness, the mold used in the C-beam press consists of accurate upper mold and some lower mold of the same size, specification and size. In order to be installed in place before processing, it is necessary to ensure not only the smooth operation of the upper and lower dies, but also the uniform gap around the upper and lower dies, so that the pressed C-section steel has a uniform wall thickness.
  在加工C型鋼的過程中,進行了模具的安裝和主機的調試。然后啟動空壓機、真空泵、擠出機、切磚機、給料機、壓磚機、主機和輸送瓦機。停止時,首先停止擠出機,然后停止其余設備。
  In the process of processing C-section steel, the installation of the die and the debugging of the main machine are carried out. Then start the air compressor, vacuum pump, extruder, brick cutter, feeder, brick press, main machine and tile conveyor. When stopping, stop the extruder first and then the rest of the equipment.
  在使用設備前,我們要檢查連接是否牢固,安裝螺栓和螺母是否擰緊,并在左右底盤上加足潤滑油后才能啟動發動機電試。擠出機的泥漿由切料機切成固定長度,由滾筒輸送機輸送到壓磚機,再由裝載機按照規定程序輸送到下模。將c型鋼壓坯在工作臺上分好后,由卸磚機的真空吸盤吸附。分度后,放置在輸送線的空白支架上。
  Before using the equipment, we should check whether the connection is firm, whether the mounting bolts and nuts are tightened, and add enough lubricating oil to the left and right chassis before starting the engine electric test. The slurry of the extruder is cut into fixed length by the cutter, transported to the brick press by the roller conveyor, and then transported to the lower die by the loader according to the specified procedure. After the C-steel blank is divided on the workbench, it is absorbed by the vacuum suction cup of the brick unloader. After graduation, it is placed on the blank bracket of the conveyor line.
  該機構制作的c梁壁厚可以很薄,大大簡化了生產過程,提高了生產效率??缮a普通熱軋方法難以生產的各種平均壁厚、復雜型材和不同材料的冷彎彩鋼設備。
  The thickness of the C-beam made by the mechanism can be very thin, which greatly simplifies the production process and improves the production efficiency. It can produce all kinds of cold-formed color steel equipment with average wall thickness, complex sections and different materials which are difficult to be produced by common hot rolling method.
  以上是濟南C型鋼廠小編為大家介紹的相關內容,想要了解更多內容,歡迎訪問網站:http://www.ebassfish.com
  The above is the relevant content introduced by the small edition of Jinan C steel works. If you want to know more, please visit the website: http://www.ebassfish.com
此文關鍵詞: 濟南C型鋼廠  

推薦閱讀/ Recommended reading

相信大家對彩鋼復合板都不會陌生,畢竟在生活中是比較常見的。雖然濟南彩鋼復合板引進不到20年時間,但由于其具有承力、保溫隔熱、裝飾、防

防火彩鋼板表面為什么出現壓斑? 2022-02-26
有哪些原因會導致C型鋼出現變形的現象? 2022-02-22
彩鋼瓦具有哪些優勢? 2022-02-17
復合板質量控制的措施及建議 2022-02-14
欧美激情视频-人妻av综合天堂一区-色天使色妺妺网站-无码a片