10年品牌值得信賴
精誠團結、奮起拼搏、開拓進取

濟南彩鋼板

13969159292

0531-88686388

新聞中心

首頁>>新聞中心>>多層鋼結構廠房的施工流程!
新聞中心
聯系我們
濟南堅固彩鋼工程公司

聯系人:

電話:13969159292

地址:濟南市工業北路81號北鄰

多層鋼結構廠房的施工流程!

來源:http://www.ebassfish.com/ 日期:2020-02-24 發布人:admin
在有限的占地面積滿足不了現代工業生產的情況下,有很多企業工廠都選擇了建造多層鋼結構廠房。但更多的只建到2-3層,這樣做的好處就是可以把一個相關的具有連貫性的生產關系,充分利用立體空間的優勢,整合在一起。不像單層鋼結構廠房那樣占用大多的地面面積,可以省出不少的建筑面積。
In the case that the limited floor space can not meet the requirements of modern industrial production, many enterprises choose to build multi-storey steel structure workshops. But most of them are only built to 2-3 layers. The advantage of doing so is to integrate a coherent production relationship and make full use of the advantages of three-dimensional space. Unlike single-layer steel structure workshop, which occupies most of the ground area, it can save a lot of building area.
今天,我們來說說多層鋼結構廠房的施工流程,首先,無論是高層還是單層,在施工前都要首先制定出工藝流程圖,確定構件的安裝順序,分區段施工。鋼結構廠房施工自然離不開起重機,無論單層或多層。
Today, let's talk about the construction process of multi-storey steel structure workshop. First of all, whether it is a high-rise or a single-layer building, before construction, we must first develop a process flow chart, determine the installation sequence of components, and construct in sections. The construction of steel structure workshop is naturally inseparable from the crane, no matter single or multi-layer.
濟南復合板廠
所以,其次需要注意的是,起重機不可以超負荷作業,在吊裝能力允許的情況下,可以再地面完成的組裝工作,我們要盡可能的避免在高空作業。
Therefore, the second thing we need to pay attention to is that the crane can not be overloaded. When the lifting capacity allows, the assembly work can be completed on the ground. We need to avoid working at heights as much as possible.
鋼結構廠房安裝前,要根據建筑物的結構形式和現場的施工條件來劃分安裝流水段。安裝流程應以從中部對稱地向四周發展,豎向根據工藝流程制定焊接順序。一節柱的各層梁安裝完后,要立即安裝樓梯以及樓承板,樓承板上的對房屋不能超過其承載。最后進行樓承板上的混凝土施工和構件的安裝。
Before the installation of the steel structure workshop, the installation flow section shall be divided according to the structural form of the building and the site construction conditions. The installation process shall be developed symmetrically from the middle to the surrounding, and the welding sequence shall be established vertically according to the process flow. After the installation of each floor beam of a section of column, the stairs and floor bearing plates shall be installed immediately, and the load on the floor bearing plates shall not exceed the load of the house. Finally, the concrete construction and component installation on the floor bearing plate are carried out.
此文關鍵詞:

推薦閱讀/ Recommended reading

相信大家對彩鋼復合板都不會陌生,畢竟在生活中是比較常見的。雖然濟南彩鋼復合板引進不到20年時間,但由于其具有承力、保溫隔熱、裝飾、防

防火彩鋼板表面為什么出現壓斑? 2022-02-26
有哪些原因會導致C型鋼出現變形的現象? 2022-02-22
彩鋼瓦具有哪些優勢? 2022-02-17
復合板質量控制的措施及建議 2022-02-14
欧美激情视频-人妻av综合天堂一区-色天使色妺妺网站-无码a片